Pieh Tool

Don’t guess the measurement of complicated curves. Just roll the traveler along the curve and count the revolutions of the 6" wheel. Measures in inches and fractions.

Features and Benefits

• High quality 14 gauge, 304 stainless steel for durability and long life
• All numbers and lines are laser etched.
• Resists rust
• Available in two styles; The Tri Square model offers a clip on stand (as shown in photo) allowing for the ruler to stand up while measuring at a right angle.

Features and Benefits

• Available in three diameters: 6", 12" and 24"
• Made of 14 gauge, 304 stainless steel and successfully resist rust.
• All numbers and lines are laser-etched into the tool.

This extremely handy tool is a must for those who need to layout accurate angles for fabrication, blacksmithing and woodworking among other situations.

The 24" is large enough to allow the layout of 1/4° increments

Quickly determine stock sizes without the hassle of a tape measure. The slots are used to determine the diameter of round stock, the size of square stock and the thickness of flat bar. The other side of the Hook Rule Gauge is used to determine the width of flat bar.

• Made of 14 gauge, 304 stainless steel and successfully resist rust.
• All numbers and lines are laser etched.

 

 Pieh Legacy Collection!

The Pieh Tool Diagonal Pien Ergonomic hammers come in Left or Right handed styles. These hammers are perfect for the blacksmith or knifemaker. The broad pein allows for better fullering.

Diagonal pein hammers are preferred by many because the pein is already positioned at a comfortable angle to make forging easier! Its compact head allows the hammer to be worked at extreme angles using the edge of the face to fuller.

Our Ergonomic Hammers are designed to move metal fast. Their compact head allows the hammer to be worked at extreme angles. Hammers are well balanced and made from 4142 tool steel and hardened to a Rockwell 52.

Each handle is ground and fit from straight grain aged hickory and then stained. The hammer handle is glued using a modern Polyurethane adhesive. This has the advantage of being able to flex during humidity and temperature changes which should give you many years of trouble free performance without the head loosening. You should always take the time to fit the handle to your hand.

Like all hand forged items each is unique and the overall weight and shape will vary slightly.

Pieh Tool Ergonomic Straight Pein hammers are perfect for the blacksmith or knifemaker. The broad pein allows for better fullering.

Our Ergonomic Hammers are designed to move metal fast. Their compact head allows the hammer to be worked at extreme angles. Hammers are well balanced and made from 4142 tool steel and hardened to a Rockwell 52.

Each handle is ground and fit from straight grain aged hickory and then stained. The hammer handle is glued using a modern Polyurethane adhesive. This has the advantage of being able to flex during humidity and temperature changes which should give you many years of trouble free performance without the head loosening. You should always take the time to fit the handle to your hand.

Like all hand forged items each is unique and the overall weight and shape will vary slightly.

Pieh Tool Standard Straight Pein Hammers are available in 2 sizes: 1.5 lbs, 2.5 lbs.

The Pieh Tool Standard Straight-Pein is an evolution of the ergonomic straight pein hammer. The head of the hammer uses a standard size eye which concentrates the hammers weight around the center rather then the ends.

In addition this style of hammer is equally weighted on both ends to allow effortless switching from face to peen. Other ergonomic hammers use a large eye which moves the weight laterally and across center mass. By keeping the overall length of the hammer short we have developed a hammer that is extremely well balanced yet has the benefit of having a less bulky handle. 

This hammers smaller eye allows the handle to retain the familiar double taper shape yet is significantly smaller. This allows a lot of comfort for those with smaller hands.  This hammer is made from 4340 and is hand forged and painstakingly heat treated.

Pieh Tool Ergonomic Cross Pein Hammers are perfect for the blacksmith or knifemaker. The broad pein allows for better fullering.

Our Ergonomic Hammers are designed to move metal fast. Their compact head allows the hammer to be worked at extreme angles. Hammers are well balanced and made from 4142 tool steel and hardened to a Rockwell 52.

Each handle is ground and fit from straight grain aged hickory and then stained. The hammer handle is glued using a modern Polyurethane adhesive. This has the advantage of being able to flex during humidity and temperature changes which should give you many years of trouble free performance without the head loosening. You should always take the time to fit the handle to your hand.

Like all hand forged items each is unique and the overall weight and shape will vary slightly.

Pieh Tool Standard Cross Pein Hammers are available in 2 sizes: 1.5 lbs, 2.5 lbs.

The Pieh Tool Standard Cross-Peen is an evolution of the ergonomic cross pein hammer. The head of the hammer uses a standard size eye which concentrates the hammers weight around the center rather then the ends.

In addition this style of hammer is equally weighted on both ends to allow effortless switching from face to pein. Other ergonomic hammers use a large eye which moves the weight laterally and across center mass. By keeping the overall length of the hammer short we have developed a hammer that is extremely well balanced yet has the benefit of having a less bulky handle. 

This hammers smaller eye allows the handle to retain the familiar double taper shape yet is significantly smaller. This allows a lot of comfort for those with smaller hands.  This hammer is made from 4340 and is hand forged and painstakingly heat treated.

This hammer is for professional farriers and blacksmiths alike. The short faces allow great balance. These hammers are made with a traditional flat/rounded face.

The Pieh Tool Standard Rounding Hammers are hand forged from 4340 tool steel then precision ground. Then, each hammer is painstakingly heat treated for a consistent and safe forging hammer.

The hammer handle is glued using a modern Polyurethane adhesive. This has the advantage of being able to flex during humidity and temperature changes which should give you many years of trouble free performance without the head loosening.  You should always take the time to fit the handle to your hand.  

Like all hand forged items each is unique and the overall weight and shape will vary slightly.

The Pieh Tool Ergonomic Hammer is designed to move metal fast. Its compact head allows the hammer to be worked at extreme angles. These hammers are well balanced and made from 4142 tool steel and hardened to a Rockwell 52.

Each handle is ground and fit from straight grain aged hickory and then stained. The hammer handle is glued using a modern Polyurethane adhesive. This has the advantage of being able to flex during humidity and temperature changes which should give you many years of trouble free performance without the head loosening. You should always take the time to fit the handle to your hand.

Like all hand forged items each is unique and the overall weight and shape will vary slightly.

Pieh Legacy Collection!

A gas forge for the Professional Blacksmiths Shop is finally available!

1. Heats 1-1/4" barstock to a yellow heat with ease!
2. Balanced Gas Mixture - only minimal scale!

Pieh Tool is excited to announce "The Smithy's" gas forge.  Our 3 burner forge was designed specifically for the artist blacksmith. It boasts the largest firebox available in the portable gas forge market!  You now have ample space to work with pieces of varying dimensions-awkward pieces can be worked that just won't fit in other forges!  Blacksmiths have been limited to forges designed for horseshoer's - with extremely small heating chambers - only 3" high, 6-9" deep and 12-13" wide.   Not any more!

This makes the perfect production shop forge because two smiths can work from both ends. The Smithy's Gas Forge has three doors that flip open allowing different access points.  The end doors also feature generous window ports for handling long pieces. Both end doors can remain open should you need the extra space while heating pieces with odd dimensions.  The front door also can be propped open. 

The heating chamber height can be reduced easily by purchasing our Smithy Forge Insert.  It all depends on your needs. This will allow you to reduce your fuel consumption when the larger space is not needed.

And finally, this forge is Insulated! We have done our utmost to help conserve your fuel costs. Just check out the specification chart below regarding the insulation used in this unit. Relining is a simple task that takes only a few minutes and requires nothing more than a 5/16" wrench.

• Professional Grade, Commercial Quality!
• Internal Volume - 1288 cubic inches!
• Fabricated with 12 gauge steel and a 5/16" frame
• High efficiency burners - Machined burner bells
• 3 Burners - Uniform heat 
• 2 Bar-stock ports
• Heats very quickly - Reaches Welding Heat easily!
• Flexible - 3 hinged doors and optional adjustable floor
• Quick and easy relining 
• Venturi Style - No blower needed
•  LP Gas
• Portable
• 9' Hose and Fisher Regulator, Pressure Gauge with POL included
• Quality Guaranteed... Pieh Tool stands behind its products
• Designed and fabricated in the USA

Operational Manual is included.

Forge can only be shipped motor freight, and arrives ready to use with only minor assembly required.

*OPTIONAL INSERT AVAILABLE!. When you have a smaller job the insert will reduce the forge height to 3 3/4". This will allow a faster heat and lower fuel usage. Gas pressure can be then be reduced to 12-15 psi.

Pieh Leagacy Collection

• The 24" hood is made of 21 gauge steel, 26" high with an 8" diameter flue pipe.   
• The forge legs and frame are fabricated from 1/4" steel.
• The hearth bed is 3/16" thick and measures: 24" wide X 30" long X 3“ high. 
• Forge also comes with an installed 11-1/2 X 14” Lorance cast iron firepot (Depth: 3-7/8; Outside Bowl Dia. At Hearth Line: 9-1/2 X 12) with clinker attached, a dumping ash gate and tuyere---all installed! 
• Our tuyere is made from a 1/4" standard cold steel welded T with welded flange.
• We use high heat paint on our forges to minimize exposure to harmful paint fumes while keeping up a professional appearance.

Pieh Leagacy Collection

Our turn-key heavy duty solid fuel forge will give you years and years of service. 

• The legs and frame are fabricated from 1/4" steel.
• The hearth bed is 3/16" thick and measures: 24" wide X 30" long X 3“ high. 
• Forge comes with an installed 11-1/2 X 14” Lorance cast iron firepot (Depth: 3-7/8; Outside Bowl Dia. At Hearth Line: 9-1/2 X 12) with clinker attached, a dumping ash gate and tuyere---all installed! 
• Our tuyere is made from a 1/4" standard cold steel welded T with welded flange.
• We use high heat paint on our forges to minimize exposure to harmful paint fumes while keeping up a professional appearance.

Pieh Leagacy Collection

Pieh Leagacy Collection

2 inch inlet, 4 inch outlet.

Forge tuyere fits our fire pot and coal forge. It has a dumping ash gate fastened by a bolt.

The Pieh Legacy Collection high volume coal/coke forge blower is specially built for Pieh Tool by Johnson Gas Co.  It features the sturdy #1203 aluminum blower housing used on Johnson's industrial furnaces. Our blower is reaady to use!  It includes wired power cord and on/off switch, mounting plate with bolts.  The air gate shutter provides quick control of air flow eliminating the need for a rheostat, which can shorten the life of a motor significantly.  Enjoy years of forging satisfaction with a Pieh Tool Blower!
Please call if you have further questions. 

Pieh Legacy Collection

The Billy Z Tongs have a V-bit jaw designed to hold flat, round and square stock. More versatily has been added to this style bolt tong because the jaw is offset (like a Z).  This not only makes it easier to hold long decorative pieces but is the perfect tong for the Knifemaker!

You are no longer limited by the length of stock you wish to work! The jaws are smooth with a deep U shaped V-notch in each jaw. The V-notch allows you to hold a larger range of thickness and widths in one pair of tongs!

Handles are slightly wider and concave on the underside.